Perle Systems - IOLAN DS1 T4

"Perle Systems - IOLAN DS1 T4" Die Ethernet-I/O- Technologie von Perle (IOLAN DS I/O Device Servers) ermöglicht den umfassenden Zugriff und die Steuerung von Remote-Digital-I/O, Analog-I/O, Puls-I/O, Relais und Temperatursensoren sowie Verbindungen von dezentralen seriellen Geräten an jedes IP-Netzwerk. Das IOLAN DS I/O kann Umgebungsalarme, Einbruchserkennung, Relaiskontaktschließungen und Geräteausfälle überwachen. Durch die Fernsteuerung des Bedieners oder der Anwendung kann das Öffnen und Schließen integrierter Relaiskontakte oder die Aktivierung digitaler Ausgangssignale in jede Reaktion auf ein kritisches Ereignis integriert werden. LIEFERUMFANG: Perle Systems IOLAN DS1 T4 ModBus, RS / / 4 Anschlüsse Enhanced Extern 10 / -TX (RL45) Eigenschaften Fernzugriff und -steuerung von digitalen I/O und Relais Universal Digital I/O, Analogeingang, RTD/Thermoelement-Temperatursensoreingang & RS-232/422/485 10/100 Ethernet-Schnittstelle mit,5 kV Isolation (802.3 Standard) Klemmenblockanschlüsse für Strom und I/O Technische Details Main Processor: MPC852T, MHz, MIPS I/O Processor: ATMEG48, MIPS Network/Ethernet: x /100Mb RJ45,.5 KV magnetic isolation I/O Connectors: Removable terminal blocks Digital I/O: or channels depending on model, software selectable as inputs or outputs, optical isolation of V rms Memory Digital Input Dry Contact: Logic = open. Logic = close to GND Wet Contact: Logic = -3VDC, Logic = VDC-30VDC Digital Output Open collector to VDC (source, sink or both), mA max load, Digital out (DO) or pulse mode Relay Form C type SPDT Contact rating: A 30VDC,.5A AC: VAC Breakdown voltage: VAC (50/60 Hz) Relay on time: msec; Relay off time: msec. Total switching time: msec. Insulation resistance: MW minimum at VDC Analog Input Channels: differential, -bit resolution Input range: ±150 mVDC, ±500 mVDC, ±1 VDC, ±5 VDC, ±10 VDC, -20 mA, -20 mA Fault and overvoltage protection: up to ±35 V Sampling rate: samples/sec. Input impedance: M Ohm Accuracy: ±0.1% or better Zero drift: ±5 µV/° C Span drift: ±25 ppm/° C CMR /60 Hz: dB min Thermocouple Input Types: J, K, T, E, R, S, B Sampling rate: samples/sec. Accuracy: ±0.15% or better Zero drift: ±5 µV/° C Span drift: ±25 ppm/° C CMR /60 Hz: dB RTD (Resistance Temperature Detector) Channels: differential inputs Input type: PT100, PT1000, Ni Sampling rate: samples/sec Accuracy: ±0.05% or better Zero drift: ±2.5 µV/° C Span drift: ±25 ppm/° C CMR /60 Hz: dB Protocols IPV6, IPV4, TCP/IP, ARP, RARP, UDP, UDP Multicast, ICMP, BOOTP, DHCP, TFTP, Telnet, raw, reverse Telnet, MODBus/TCP, RCP, WINS, HTTP, SNMPV3 Management Via Web browser, Perle DeviceManager software to manage single or multiple device servers, CLI – Telnet or shared console port, Menu, SNMP, MIB II, Perle MIB, read and write capabilities, SYSLOG, Easy Configuration Wizard Failsafe mode: Default outputs if loss of communication occurs, Set a personalized factory default for IOLANs Serial Port Software selectable EIA/RS-232/422/485, DB9M connector, Full modem and hardware flow control on RS-232, bps to Kbps for EIA-232, Customizable baud rate support for unique speed requirements, up to Kbps for EIA-422/485, SUN Break Safe, Full bidirectional modem support, Kv ESD protection on all signals, EIA full duplex, EIA full duplex, EIA wire, full duplex, EIA wire, half duplex, with echo, EIA wire, half duplex, without echo Indicators Power/Ready, Network Link activity Serial: Transmit and Receive data LEDs Power 9-30V DC on terminal blocks, Optional AC adapters available from Perle, p/n (USA), (UK), (EU) Environmental Operating Temperature: °C to °C (32 F to F) Storage Temperature: -40° C to ° C (-40 F to F) Chassis: Metal with an IP30 ingress protection rating Product Weight and Dimensions Weight:.5 kg Dimensions:.7 x.2 x.5 (cm)